rssLink RSS for all categories
 
icon_red
icon_green
icon_red
icon_red
icon_blue
icon_green
icon_green
icon_red
icon_red
icon_red
icon_orange
icon_green
icon_green
icon_green
icon_green
icon_blue
icon_green
icon_orange
icon_red
icon_green
icon_red
icon_red
icon_green
icon_red
icon_red
icon_red
icon_red
icon_orange
icon_green
 

FS#3468 — FS#7411 — vss-9b-6k

Attached to Project— Network
Incident
Whole Network
CLOSED
100%
The card 6 of the router is defective. We will change the
DFC.

Routing is ensured by the other cards and the router
vss-9a-6k

Oct 3 11:00:11.200: %C6KERRDETECT-SP-2-SWBUSSTALL: The switching bus is experiencing stall for 3 seconds
Oct 3 11:00:12.200: %C6KERRDETECT-SP-2-SWBUSSTALL_RECOVERED: The switching bus stall is recovered and data traffic switching continues
*Mar 1 00:00:02.823: DaughterBoard (Distributed Forwarding Card 3)
Firmware compiled 24-Jan-11 15:17 by integ Build [100]
Oct 3 11:01:39.272: %SYS-DFC3-5-RESTART: System restarted --
Cisco IOS Software, c6lc2 Software (c6lc2-SP-M), Version 12.2(33)SXI7, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Mon 18-Jul-11 05:49 by prod_rel_team
Oct 3 11:01:39.280: DFC3: Currently running ROMMON from S (Gold) region
Oct 3 11:01:44.464: %DIAG-SP-6-RUN_MINIMUM: Module 3: Running Minimal Diagnostics...
Oct 3 11:03:41.397: %DIAG-SP-6-DIAG_OK: Module 3: Passed Online Diagnostics
Oct 3 11:03:41.725: %OIR-SP-6-DOWNGRADE_EARL: Module 3 DFC installed is not identical to system PFC and will perform at current system operating mode.
Oct 3 11:03:43.052: %OIR-SP-6-INSCARD: Card inserted in slot 3, interfaces are now online
Oct 3 12:48:04.072: %SYS-5-CONFIG_I: Configured from console by flo on vty21 (213.186.33.13)
Oct 3 12:48:16.812: %SYS-5-CONFIG_I: Configured from console by flo on vty21 (213.186.33.13)
Oct 3 13:17:03.894: %SYS-5-CONFIG_I: Configured from console by flo on vty21 (213.186.33.13)
Oct 4 09:36:55.807: %OIR-SP-6-PWRFAILURE: Module 6 is being disabled due to power convertor failure. PMB registers are dumped as follows, R0= 0x2, R1= 0x2, R2= 0x0, R3= 0x0, R4= 0x0, R5= 0x1, R6= 0x0, R7= 0x2, R8= 0x0, R9= 0x0, R10= 0x0, R11= 0x0, R12= 0x0, R13= 0x0, R14= 0x0, R15= 0x0
Oct 4 09:36:55.807: %C6KPWR-SP-4-DISABLED: power to module in slot 6 set off (FRU-power failed)

Date:  Thursday, 04 October 2012, 22:00PM
Reason for closing:  Done